70 Series (up to 1989) BJ70, BJ71, BJ73, BJ74, BJ75

Seal, Rear Inner Axle Shaft - Full Floater - Land Cruiser 40, 60, 70, 80 Series

90310-35001

Spindle Bushings for Land Cruiser and Hilux with the solid front axle.
1 piece per spindle required
Toyota pn:
90381-33002
90999-70067

Split Transfer Case input shaft support bearing (for H41, H42, H55F & others), 1981-on

Spring, Oil Pressure Relief Valve - 12HT, 2H, 3B

Toyota pn:
15132-76011

Toyota - Japan

Spring Bushing Kit - Land Cruiser 40, 60, 70 series & 77 series front springs - 35mm OD

Steering Knuckl Stud - “hexalobular” (=has 6 point male torx at the top for tightening into place).

This is the new. updated part from Toyota that replaces all knuckle studs from early versions. It is slightly longer than the previous versions, and has

DT-SH4 Swivel Hub/Knuckle Kit

Fits all Land Cruiser models up to 1989 with Non-High Pinion front end.

Tail Lamp Assembly, LH - Land Cruiser 70 Series HD - BJ70, BJ71, BJ73, BJ74, HZJ70, HZJ73

81560-90K03
81560-60400
81560-69135

Tail Lamp Assembly, RH - Land Cruiser 70 Series HD - BJ70, BJ71, BJ73, BJ74, HZJ70, HZJ73

81550-90K03
81550-69135
81550-60480

Thermostat - Toyota 3B, 13BT, 2H, 12HT
82C/180F version of the 13BT & 3B thermostat
Toyota pn:
90916-03102

Toyota OEM - Japan

Thermostat - Toyota 3B, 13BT, 2H, 12HT 88C/190F

90916-03103

Thrust/Lock “claw” Washer, Spindle Bearing, Front Outer - Land Cruiser 09/1975-on

90214-42030

Tie Rod End - RHD - Left Outer - Land Cruiser 60 & HD 70 Series <1990

Tie Rod End Kit - RHD - Land Cruiser 70 Series Heavy Duty <1989

Tie/Relay Rod End - RHD - RH Inner - Land Cruiser HD 70 Series (Early)

45044-69075

Sankei 555 - Japan

Toyota 3B timing gear casing with oil pump & relief valve

Toyota pn: 11301-56030

Tool, Hub Nut Socket 55mm (Toyota 54mm)
Made in China

Clutch kit for Toyota 3B engines as found in BJ42, BJ60, BJ70 & other applications.

This is a 5 piece kit includes the centering tool and pilot bearing .

Exedy Clutch - Japan

Toyota 3B Full Engine Gasket Kit
-> see product description below for details

Transfer Case Output Bearing for Land Cruiser split transfer case, 1981-on

Universal Joint - Land Cruiser 40, 55, 60, 70 & 80 Series. 64mm u-joint that was used from 1974 (with the introduction of the 4 speed transmission)
04371-36030
04371-60210
Toyota - Made in Japan

Universal Joint - Land Cruiser 40, 55, 60, 70 & 80 Series.
This is the larger 64mm u-joint that was used from 1974 (with the introduction of the 4 speed transmission) & up.
04371-36030
04371-60210
GMB - Made in Japan

Water Pump 3B & 13BT - later models
Land Cruiser BJ60, BJ70, BJ71, BJ73, BJ74, BJ75 & related vehicles with late model 3B engines.
Toyota pn: 16100-59105
NPW - Made in Japan
Note: These pumps do not suit early 3Bs with 6mm fan studs.

Wheel Bearing Kit, Front & Rear - Land Cruiser & Hilux Full Floating axles (excluding rear disc brake models)
Koyo Bearings in kit