Transmission & Drive Train

10 spline Input shaft for H55F transmissions with the 2H or 12HT engine as found in HJ60, HJ61, HJ45, HJ75 etc.

Replaces
33311-60121

Taiyo Kiko Mfg Ltd. - Made in Japan

31230-60130

Nachi (OEM) - Japan

1HZ & 13BT 3 Pc. Clutch Kit "Sports Tuff" Heavy Duty - Exedy Japan
3 piece kit
- clutch disc 275mm x 21 spline
- pressure plate
- release bearing
**pilot bearing sold separately
Exedy - Japan

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 8” High Pinion Differential
These are the alternative higher ratio for Land Cruiser 80 Series with high pinion 8” differentials.
41201-69226
OEM - Made in Japan

Clutch Slave Cylinder - BJ40/2 & early BJ60 - short clutch slave
31470-60050
31470-60110
Made in Japan

Front Lateral Control Arm/Panhard Rod Bushing - Upper & Lower - Land Cruiser 80 Series (2 req = 1 per end)

Toyota pn:
48706-60030

Aftermarket - Thailand

8708.29

8mm Hub Stud Kit - Toyota Land Cruiser, Hilux & other Toyota models
Toyota pn:
90116-08325
90170-08204
94512-00800
42323-60010

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 9.5” Differential (1990-on)

Made in Japan

Axle Shaft, Left Front Inner (long) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on

Axle Shaft, Right Front Inner (short) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on

Bearing Kit, Transfer Case - Land Cruiser split case - 10/1982-10/1985 with H55F 5 speed and 34 mm idler shaft

Bearing Kit, Transfer Case - 34mm Land Cruiser split case for 4 speed up to 10/1982

Bearing Kit, Transfer Case - Land Cruiser split case - 5 speed - 10/85-on, with 38mm idler shaft

This kit contains all of the gaskets, seals, bearings, 38mm idler shaft to rebuild your Land Cruiser split case from a 5 speed model from 10/1985-on.

This kit contains all of the gaskets, seals, bearings, 38mm idler shaft to rebuild your Land Cruiser split case from an Automatic Transmission model from 10/1985-on.

The bearings are all Koyo - Made in Japan

Bearing, Differential Carrier - Toyota Land Cruiser high pinion 8” E-Locker RH side

Bearing, N307LOE (shallow type) for SM420 Adapter Plate

These are the correct Koyo knuckle (aka trunion or king pin) bearings for your pre-1990 Toyota solid axle vehicle.
Toyota part number: 90366-17001-77
Koyo part number: TR0305A
Koyo - Japan

Replacement Birfield CV Axles for the Land Cruiser 80 Series. Non-ABS.

These are the later versions with the longer splined section that replace the early short splined versions that were prone to premature spline/drive flange wear.

Toyota pn:
4340

Replacement Birfield CV Axles for the Land Cruiser 80 Series.

These are the later versions with the longer splined section that replace the early short splined versions that were prone to premature spline/drive flange wear.

Suits models with ABS.

Birfield CV Axle, Nissan Safari/Patrol GQ Y60 Series 07/1989-12/1997

Birfield CV Axle, Toyota Land Cruiser 70 Series - 8" High Pinion (08/1989 - On)

Toyota pn:
43405-60040

Extreme Duty Clutch Kit for Toyota Land Cruiser HZJ70, HZJ73, HZJ77

Extreme Duty clutch kit - has far more clamping force than the stock Toyota clutch.

Pedal effort will be considerably more than with either the Sports Tuff of Regular grade clutch kit.

Clutch Kit for Toyota Land Cruiser HZJ70, HZJ73, HZJ77

The Exedy ‘Regular Duty’ clutch kit is a stock replacement kit, and has slightly more clamping force than the stock Toyota clutch.

Flywheel must be machined with a +0.5mm step as per factory specif

Master Cylinder, Clutch - Land Cruiser BJ70, BJ73, HJ75 3B, 13BT 10/1985-on (1 stud, 1 bolt hole)