Axle

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 8” High Pinion Differential
These are the alternative higher ratio for Land Cruiser 80 Series with high pinion 8” differentials.
41201-69226
OEM - Made in Japan

Front Lateral Control Arm/Panhard Rod Bushing - Upper & Lower - Land Cruiser 80 Series (2 req = 1 per end)

Toyota pn:
48706-60030

Aftermarket - Thailand

8708.29

8mm Hub Stud Kit - Toyota Land Cruiser, Hilux & other Toyota models
Toyota pn:
90116-08325
90170-08204
94512-00800
42323-60010

3.73 Ring & Pinion Gear Set - Toyota Land Cruiser 9.5” Differential (1990-on)

Made in Japan

Axle Shaft, Left Front Inner (long) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on

Axle Shaft, Right Front Inner (short) - Land Cruiser 80, 105 Series w/8” High Pinion 01/1990-on

Bearing, Differential Carrier - Toyota Land Cruiser high pinion 8” E-Locker RH side

These are the correct Koyo knuckle (aka trunion or king pin) bearings for your pre-1990 Toyota solid axle vehicle.
Toyota part number: 90366-17001-77
Koyo part number: TR0305A
Koyo - Japan

Replacement Birfield CV Axles for the Land Cruiser 80 Series. Non-ABS.

These are the later versions with the longer splined section that replace the early short splined versions that were prone to premature spline/drive flange wear.

Toyota pn:
4340

Replacement Birfield CV Axles for the Land Cruiser 80 Series.

These are the later versions with the longer splined section that replace the early short splined versions that were prone to premature spline/drive flange wear.

Suits models with ABS.

Birfield CV Axle, Nissan Safari/Patrol GQ Y60 Series 07/1989-12/1997

Birfield CV Axle, Toyota Land Cruiser 70 Series - 8" High Pinion (08/1989 - On)

Toyota pn:
43405-60040

Crush Sleeve - Land Cruiser 9.5" Differentials

Differential Bearing Kit - Land Cruiser 9.5" - 50mm Carrier Bearings & Crush Sleeve (1990-On)

Differential Bearing kit - Land Cruiser 9.5" - w/Crush Sleeve

Differential Bearing kit - Land Cruiser 9.5" with Factory Locker (e-locker, cable locker)

Differential Bearing Kit - Land Cruiser High Pinion 8" w/Factory Locker

This kit is for a non e-locker differential. The e-locker differential uses 2 different carrier bearings. 90366-75001 needs to be supplied for e-locker applications.

Kit Contents:
90366-50007 x2 - Carrier Bearings (83mm od)
90366-35028 x1 - Inn

Differential Carrier Bearing - Land Cruiser 9.5" up to 1989 (45, 79)
Toyota pn:
90368-45001

Fits the front & rear differentials that are 9.5” and some front diffs in the 8” high pinion configuration - there are two sizes for the fronts: 80mm outer dia., and 83mm outer dia.

The 83mm outer diamter is the 90366-50007 bearing and not this one.

Koy

Drive Flange, Front Axle - Land Cruiser 80 Series with longer splines.
43421-60040

Toyota OEM or Joint Fuji - Japan

Dust Seal, Rear - Land Cruiser Full Floating Axle 4-bolt (08/1980-08/1989)

90313-93001

Electric Locking Hub Adapters - these allow you to replace the Toyota Aisin Electric Locking Hubs with Aisin or manual hubs
Kit Contents:
2x CNC machined adapters w/hardware & gaskets
Made in Canada

Drive Flange - Land Cruiser 80 Series - Short splined drive flange for the early Birfield CV Axles.

43421-60020

Joint Fuji - Made in Japan